|3 Year Residential 1 Year Commercial
This engine comes with a 3 year Residential and 1 year Commercial Use Warranty
|Optimized Capacity-Rigid Type Muffler
Optimized-capacity rigid muffler and 33 percent fewer moving valve
train parts than OHV designs reduce mechanical noise levels a full 2
decibels below competitive models.
|Dual Ball Bearing Support
Dual ball bearing crankshaft support offers maximum stability under demanding loads.
Cast-iron cylinder liners enhance reliability and extend engine
life.The cast-iron cylinder liner has much better wear characteristics
the softer aluminum that surrounds it, making engine life much longer
than if the piston is in contact with the aluminum cylinder wall.
|Forged High-Carbon Steel Crankshaft
Forged high-carbon steel crankshaft provides maximum reliability under demanding loads, thus providing longer engine life.
The drop forging process increases the strength and durability of the
crankshaft by re-aligning the molecules in the steel. This process
hardens the complete crankshaft. Most engines use cast-iron steel
|High Power Pent-Roof Design
Overhead Cam (OHC) technology and the Pent-Roof combustion chamber
allow the Subaru SP engines to use a higher compression ratio of 9:1.
The higher compression ratio increases the power produced for a given
size engine. It also improves efficiency and overall performance.
|Component Location Cutaway
The cutaway shows some common parts on the Overhead Cam SP engine series.
|High Efficiency Intake Port
The illustration shows the straight intake port on the right side of
the picture. The lower resistance to the flow of the air/fuel mixture
improves the power, efficiency and lowers emissions. Overhead Cam (OHC)
technology allows the intake and exhaust valves to be positioned for
|Camshatt with Automatic Decompression Release
The camshaft and the sprocket are made of special sintered alloy and constructed as a single piece. The camshaft is provided with intake
and exhaust cam in one cam lobe. The decompression release lever is
mounted on the sprocket end side.
|Hardened Steel Rocker Arms
Hardened steel rocker arms with precision tappet adjusters are used for greater durability and reduce service requirements.
|Patened Pending Main Bearing Cover Design
An internally structured main bearing cover offers patent-pending technology by creating a highly rigid engine system.
|Automotive Collets & Forged Steel Valve Retainers
Subaru SP Series engines use automotive quality collet valve retainers for longer life.
Special machining on cylinder head allows the oil seal to be placed
around the valve guide. This seal reduces oil consumption and is
replaceable for service.
|Patent-Pending Connecting Rod Dipper
The SP Series lubrication system begins with a patent-pending oil scoop to project the oil to the chain.
|Aluminum Alloy Die-Cast Connecting Rod
The connecting rod is a specially heat-treated aluminum alloy
die-casting, Its large and small ends function as bearings. A splasher
built into the connecting rod lubricates by splashing engine oil. The
piston is an aluminum alloy casting with grooves for mounting
compression and oil rings.
|Mounting Base Cooling Fins
The unique Subaru cooling system extends to the underside of the
mounting base. Air is forced over special cooling fins at the bottom of
the engine for maximum cooling.
|Cylinder Head 360 Degree Cooling
Head cooling is critically important to long engine life. The Overhead
Cam design allows for 360-degree air flow around both the exhaust and
intake valve stem areas.
Cooling fins are cast into both the inside and the outside of the crankcase to utilize every possible cooling area.
|Patent-Pending Cylinder Cooling Fins
Air is forced over the large slanted cooling fins on the cylinder for
improved cooling performance. This design is patent-pending.
|Patent-Pending Valve Cover Design
A patent-pending valve cover design constantly
supplies an optimum amount of oil to the cam
shaft and rocker arm even if the engine is
|Patent Pending Breather System
A patent pending breather system with a pre-separation
passage prevents oil from spouting, even if the engine is inclined.
|Hot Spark Ignition System
The ignition system is a transistor controlled magneto with the
ignition timing set at 23 degrees before top dead center. The magneto
consists of a flywheel and ignition coil. To ensure the easy
startability of the engine, the step advancing ignition timing system
is incorporated in the ignition coil. This system enables the engine to
have basically two different ignition timings according to the engine
Even though the SP series engines bring the latest technology,
performance, and durability to the industrial air cooled engine market,
there are no special tools required to work on them. Most
shop tools that small engine mechanics currently own, will also
work on these engines for service or complete tear down. Subaru engineers have achieved their commitment to 'keep it simple', while utilizing the latest technology.